Bd N1134 User Manual

QLD Office: 17 Oasis CourtClontarf 4019(07) 3883-0200NSW Office: 34-36 Marigold StreetRevesby 2212(02) 9722 5555VIC/TAS Office:147-153 Canterbury Road

BoltTrolley Stop Bolt HoleLockWasherNutBoltNutLock WasherWasheredBoltSprocket2Stops4SprocketSpreaderStopsSpreaderScrewdriver TipNut RingWrenchSpring N

11IMPORTANT INSTALLATION INSTRUCTIONS1. READ AND FOLLOW ALL INSTALLATIONWARNINGS AND INSTRUCTIONS.2. Install garage door opener only on properlybalanc

12INSTALLATION STEP 1Determine the Header BracketLocationInstallation procedures vary according to garage doortypes. Follow the instructions which app

13One Piece Door Without Track1/30/92 - 4/7/92 HeaderWallVerticalCentrelineVerticalCentrelineof GarageDoor40mmReinforcementBoardUnfinishedCeilingOPTIO

14INSTALLATION STEP 2Install the Header BracketWALL HEADER BRACKET INSTALLATION• Centre the bracket on the vertical guideline with thebottom edge of t

15Ring fastener (2)Temporary SupportGarage DoorHeader WallHeader BracketHeader Sleeve BracketClevis PIn8mm x 13mm (2)Ring FastenerRing Faste

16Top of Motor UnitHeaderBracketTop of doorDoorONE-PIECE DOOR WITHOUT TRACK• With the door fully open and parallel to the floor,measure the distance f

17114A2845INSTALLATION STEP 6Install the door controlLocate the door control within sight of the door at aminimum height of 1.5m where small childrenc

18WIRING INSTRUCTIONS FORACCESSORIES• Place entrapment warning label on the inside ofdoor as a reminder of safe operating procedures.Place the manual

19114A2845Overhand KnotEmergency Release HandleTrolley Release ArmNOTICEThe Chamberlain Group, Inc.Figure 16 - Manual Release4210E - 3/8/93RopeTroll

2Introduction 2-7Safety rule review...2Preparing your garage door ...

20Invisible Light BeamProtection AreaThe Chamberlain Group, Inc.Safety SensorInstruction Sheet Page 1 Protector System Disk #1 (Yellow)11/5/91 -

21Carriage Bolt 8mm x 65mmNut 8mmLock Washer 8mmSheet Metal ScrewHARDWARE SHOWN ACTUAL SIZE114A2845Fibreglass, aluminum or lightweight steel garage do

22Carriage Bolt 8mm x 65mmNut 8mmLock Washer 8mmSheet Metal ScrewHARDWARE SHOWN ACTUAL SIZE114A2845Header WallVerticalCentreline ofGarage DoorFinished

23INSTALLATION STEP 12Connect Door Arm to TrolleyFollow instructions which apply to your door type asillustrated below and on the following page.SECTI

ALL ONE-PIECE DOORSAssemble the Door Arm:• Fasten the straight and curved door arm sectionstogether to the longest possible length (with a 2 or3 hole

25ADJUSTMENT STEP 1Limit AdjustmentRun the opener through a complete travel cycle.Force adjustments are not necessary when the dooropens and closes co

ADJUSTMENT STEP 2Adjust the ForceThe force, as measured on the closing edge ofthe door, should not exceed 400N (40kg). If theclosing force is measured

ADJUSTMENT STEP 3Test the Safety Reverse SystemTEST• With the door fully open, place a 40mm board onthe floor, centered under the garage door.• Operat

28Using Your Garage Door OpenerYour opener will operate with up to twelve remotecontrol transmitters, one entry keypad, and one dip-switch code transm

29To Open the Door ManuallyDISCONNECT THE TROLLEY:The door should be fullyclosed if possible. Pull downon the emergency releasehandle (so that the tro

3PliersWire CuttersClaw HammerHack SawScrewdriverAdjustable End WrenchLocking pliers13mm, 11mm, and 6mmSockets and WrenchDrillTape Measure21Stepladde

Troubleshooting1. Opener doesn't operate from either door control orremote:• Does the opener have electric power? Plug lamp into outlet.If it doe

31To Erase All Codes From OpenerReceiver MemoryTo deactivate any unwanted remote,first erase all codes:Press and hold the “Learn” button onopener unti

114A2845 ©2005, All Rights Reserved Printed in MexicoWARRANTYControll-A-Door®Automatic Garage Door Opener1.Definitions‘B&D’ means (a) in Australia

Safety Reversing SensorHorizontal and vertical reinforcementis needed for lightweight garage doors(fibreglass, steel, aluminum, door with glass panels

5AccessDoorGap between floor and bottom of door must not exceed 6mm.SafetyReversing SensorThe Chamberlain Group, Inc.One-Piece Door with Track Install

6Your garage door opener is packaged in two cartonswhich contains the motor unit and the parts illustratedbelow. If anything is missing, carefully che

Hardware InventorySeparate all hardware and group as shown below for the assembly and installation procedures.7Spring /Trolley Nut (1)MasterLink (2) A

8ASSEMBLY STEP 1Assemble the RailNOTE: If your opener came with a one piece rail,proceed to Assembly step 2, page 9.Grease inside edges of rail brace

9ASSEMBLY STEP 3Attach Chain SpreaderAttach chain spreader to opener with phillips panhead screws.Chain SpreaderPhillips Pan Head ScrewsOpenerTo avoid